manual Glue Dispensing Table Label PVC Dispenser 200W

KY-0306 Hand Working High Effeicency Glue Dispensing Table Clothing Label Producing Machine

Description:

When operating a manual silicone dispensing table, you may encounter some common issues or challenges. Here are a few troubleshooting tips to help address them for example: Remember to consult the user manual or contact the manufacturer for specific troubleshooting guidance and support related to your manual silicone dispensing table.

1. Uneven Dispensing or Inconsistent Flow:

   • Check the viscosity of the silicone material. If it's too thick, it may not flow smoothly. You can try warming the silicone cartridge or syringe slightly to improve its flow characteristics.
   • Ensure that the dispensing gun and nozzle are clean and free from any clogs or obstructions. Clean them thoroughly if necessary.
   • Verify that the dispensing gun is properly assembled and tightened. Loose connections can lead to inconsistent flow.
   • Adjust the pressure and speed of the dispensing gun. Experiment with different settings to achieve a more consistent flow.

Quick detail:

1. 1. Air Bubbles in Dispensed Silicone:

2. Eliminate air bubbles from the silicone material before dispensing. Follow the recommended degassing or mixing procedures provided by the manufacturer.

   • Prime the dispensing gun at the beginning to purge any trapped air. Squeeze the trigger a few times until a steady flow of silicone is achieved.
   • If air bubbles still occur during dispensing, try adjusting the dispensing speed or angle to minimize their formation.

• 2. Difficulty Controlling Dispensing Lines or Patterns:

  • Practice your technique by adjusting the speed and pressure of the dispensing gun. Slower speeds and lighter pressure can provide greater control over the dispensed lines or patterns.
  • Experiment with different nozzle or applicator tip sizes and shapes to achieve the desired results.
  • Use guide rails or templates to help guide the dispensing gun along a straight line or specific pattern.

• 3. Clogging or Blockages:

  • Ensure that the silicone material is properly prepared and free from any contaminants or foreign particles.
  • Clean the dispensing gun, nozzle, and other components regularly to prevent any residual silicone from hardening and causing blockages.
  • If a blockage occurs, disassemble the dispensing gun and clean the affected parts thoroughly. Use appropriate cleaning agents or solvents as recommended by the manufacturer.

• 4. Inconsistent Curing or Adhesion:

  • Verify that the curing conditions, such as temperature and humidity, are suitable for the silicone material being used. Follow the manufacturer's instructions for optimal curing.
  • Ensure that the label substrate or mold is clean and properly prepared to promote good adhesion.
  • If necessary, consider using a primer or adhesion promoter on the label substrate to enhance bonding with the silicone material.

• 5. Equipment Maintenance:

  • Regularly inspect and maintain the dispensing equipment according to the manufacturer's recommendations.
  • Replace worn or damaged parts, such as worn-out nozzles or dispensing gun components, to ensure optimal performance.
  • Keep the work surface clean and free from any residue that could interfere with the dispensing process.

Advantage(Company introduction):

Located in Shunde district-Shunde National High-Tech industrial zone in Foshan city, Foshan KaiYu Machinery CO.,LTD established in 2002. Main products including Digital Automatic Vacuum Vulcanize Machine,Bump Printing Machine, Automatic Dispensing Machine, Dispensing Table, High Frequency Machine, Automatic Vacuum Cabinet, Freezing Table, Water Chiller, Gluing machine, Sand Blasting Machine, Baking Table, Micro-injection Trademark Line, Tools and related materials . Products are sold to many countries all over the world. We have professional and technical personnelto provide you with professional after-sales service and technical guidance for a long time,and also ready live demonstration for your.
Welcome all customers'visiting to discuss cooperation for win-win result.

PVC Glue Dispensing Table

200W Glue Dispensing Table

200W pvc dispenser

manual Glue Dispensing Table Label PVC Dispenser 200W Images